Electric Pipe Threader
 |
 RIDGID 700 PORTABLE PIPE THREADER HAND HELD ELECTRIC GREAT  US $363.00
|
 RIDGID PIPE THREADER POWER PONY WITH DIES US $600.00
|
 NEW ARMATURE FOR RIDGID 300 535 FITS PART 44010 115V US $112.00
|
 2 Portable Electric Pipe Threader Threading Machine 6 Dies US $259.99
|
 GREENLEE 855 555 Conduit Pipe Bender EMT RIDGID IMC US $6,550.00
|
 GREENLEE 555 Conduit Pipe Bender 5 SHOES 4 ROLLERS US $6,465.00
|
 10 piece Electrician’s Holesaw Kit US $37.71
|
 PORTABLE ELECTRIC PIPE THREADER WITH 4 DIES TOOL 2000W US $164.99
|
 Portable Electric Pipe Threader 6 Dies 1800W US $289.99
|
 NYE 2629888 PIPE THREADER HEAD DIES NO 51B 1 TO 2 US $134.00
|
 REED CT4 SUPER DUTY TRI STAND PIPE THREADER CHAIN VISE US $175.00
|
 PT Reamer fits RIDGID ® 300 Pipe Threader Ridg42365 US $64.99
|
 OSTER 552 NZ 3999 ELECTRIC PIPE THREADER USED US $500.00
|
 Ridgid Pipe Threader Die Head Cutter Set 111R 773 12R US $179.00
|
 ridgid 1 1 4 PIPE die head PARTS FOR 300 535 threader US $25.00
|
 WHEELER REX PIPE THREADER 6590 WITH EXTRAS US $4,989.00
|
 15 piece Plumber’s Holesaw Kit US $67.95
|
 RIDGID 535 A 3 SPEED POWER PIPE THREADER ROLLER STAND 5 US $4,500.00
|
 Ridgid 161 Threader 4 to 6 Pack 300 535 700 New Dies US $3,199.99
|
 RIDGID 535 POWER PLUMBING PIPE THREADER REAMER CUTTER B US $2,650.00
|
 NEW GREENLEE 854 555 Conduit Pipe Bender EMT RIDGID IMC US $8,995.00
|
 NEW GREENLEE 855 555 Conduit Pipe Bender EMT RIDGID IMC US $10,895.00
|
 Wheeler SideKick ll Pipe Threading Machine 1 2 1 US $1,700.00
|
 Portable Electric Pipe Threader w 6 Dies 1800W US $279.99 |
 RIDGID PIPE THREADER 400 US $389.00
|
 4 Piece Pipe Threader 1 2 To 1 1 4 US $51.95
|
 24 HP Electric Pipe Threader 1 2 2 NeikoUSA US $269.99
|
 Central Machinery Portable Pipe Threader NEW IN BOX US $179.00
|
 Rems Pipe threader Amigo series 2 For 1 Pricing US $725.00
|
 RIDGID 500 PIPE THREADER MACHINE 300 700 US $1,200.00
|
working a pipe threader?
Any info on tips or operation of a electric threader.
Is this a hard machine to use. Thanks
Its basically pretty easy to do . I assume you will be using a ridgid brand threader.
Long pipes will have to be supported at the end leaving the threader. Pipe lenghts of arround 4 feet you do not need the support stand.
Keep the threads well lubricated when cutting to keep the die teeth cool.
Don't over thread... pipe threads are tapered at 3/4 inch per foot. The male and female threads are both tapered so the joint becomes a crush fit to seal the joint. (pipe dope is also recommended either teflon tape or rector seal #5)
The depth of the die cutting teeth are set at this taper. If you thread beyond this depth then the extra depth leaving the die will not have a taper and can bottom out in your fitting before properly engaging and sealing the joint.
The ridgid threader has a quick release on the threading attachment. The teeth are brought into cutting position with the lever. as the die nears the completion of its cut you stop the cutting by opening the teeth with this lever and stopping the maching. There should be a foot switch to start the motor, also make sure thatthe direction switch is set to forward.
Cutting teeth need to swapped for different size pipes. consult a thread chart for the proper pitch. The quick release threader attachment also has an adjustment for pipe size. The same pitch can be use on several sized pipe. Also make sure that all three sets of cutting teeth are the same size (pitch)
The first operation is usuall cutting the pipe to lenght.. this can be done by having the machine turn the pipe and operate the cutter braced against the rails.
After the pipe is cut the pipe inside diameter is reamed out with a tapered reamer to remove chips and create a smooth surface.
The pipe end is then threaded